Oil tanks can be located in many different places. Oil tanks were out of sight and out of mind.  Many oil tanks can be found buried under the lawn or driveway.  Some oil tanks were buried to never been seen again, oil tanks can be buried under garage floors, decks and under the home itself such as under a sun room.  (Photo below is a tank under the floor of a room).

Oil tanks are only a problem when they leak, since leaky tanks may require remediation.  The only way to know if an oil tank is not leaking is by testing the soil under the tank.  Oil tank removal is typically your best option, since once the tank is removed, you can access soils under the tank to sample.     With tanks that are under a building, you options open up from either removal (typically possible, just expensive) to closure in place, which is the more affordable and practical option.

(Photo below shows how a tank sweep found where under the floor the tank was located)

Oil tank closure in place can address concerns with the oil tank, by cutting holes in the bottom of the tank (after the tank is thoroughly cleaned) and taking soil samples.

By going through the bottom of the tank you can access the soils where samples are supposed to be acquired to assess for leaks.

It's not easy work, but its cheaper than removing the tank.

The photo below shows the holes (coupons) cut in the bottom of the tank to access the soils.

Our clients hire Curren to find professional affordable solutions and with close to thirty years experience we have solved a lot of problems with oil tanks.  The photo above shows a tank under a room that we excavated, cleaned and obtained site assessment soil samples.  

This small hole was all that was required for closure in place of this tank.  Removal of the tank would have required that half the floor in the room be removed, and may have undermined the walls requiring structural support.  Curren's tank closure in place was the appropriate and lowest cost solution.

Certified in New Jersey, Pennsylvania & Delaware for tank closure.

Thousands of completed projects.

Professionals solutions is a phone call away.

On December 8, 2019 the NJDEP presented a link to a document presenting the NJDEP’s position on the use of rounding analytical data in order to achieve compliance with regulatory cleanup criteria.  This rounding practice has been primarily used with respect to groundwater data.  Under the “What’s New!” column on the right hand side of the page, fourth item down titled Notice Concerning the Use of Rounding of Analytical Data as a Method to Determine Compliance with Remediation Standards. The message can be found here. 

As stated, the NJDEP “does not have an official policy regarding rounding as a method of compliance” and that “current laws and rules regarding remediation do not address rounding as a method of compliance”.  The NJDEP has also indicated that “rounding of analytical data may not be used as a compliance option”.

According to the Site Remediation Reform Act, N.J.S.A. 58:10C-1 et seq, which is law,  states as follows; 

58:10C-14. Certification of documents by site remediation professional

(3) The licensed site remediation professional shall apply any available and appropriate technical guidelines concerning site remediation as issued by the department. The department shall provide interested parties the opportunity to participate in the development and review of technical guidelines issued for the remediation of contaminated sites.

(4) When there is no specific requirement provided by the technical standards for site remediation adopted by the department, and guidelines issued by the department are not appropriate or necessary, in the professional judgment of the licensed site remediation professional, to meet the remediation requirements listed in paragraph (1) of this subsection, the licensed site remediation professional may use the following additional guidelines to make decisions regarding a remediation, and shall set forth justification for such use, in the relevant submittal:

(a) relevant guidance from the federal Environmental Protection Agency or other states; and

(b) other relevant, applicable, and appropriate methods and practices that ensure the protection of the public health and safety, and of the environment.

As shown above section 58:10C-14c(4) indicates that in the absence of official regulations and/or guidance by the NJDEP, the LSRP may rely upon other credible guidance in order to make decisions regarding their oversight of a remedial site.

More information on the USEPA document titled Procedures for Rounding-Off Analytical Data to Determine Compliance with Maximum Contaminant Levels Present in NIPDWR, April 6, 1981 can be found here.

The document refers that all Maximum Contaminant Levels (MCL) contained in the National Interim Primary Drinking Water Regulations are expressed in the number of significant digits permitted by the precision and accuracy of the specified analytical procedure(s). Data reported to the State or EPA should be in a form containing the same number of significant digits as the MCL. In calculating data for compliance purposes, it is necessary to round-off by dropping the digits that are not significant. The last significant digit should be increased by one unit if the digit dropped is 5, 6, 7, 8 or 9. If the digit is 0, 1, 2, 3, or 4, do not alter the preceding number.

For example, if the monthly mean for coliform bacteria is 1.4999, the reported result should be 1 (one). A result of 3.50 should be rounded to 4 (four).

Chemical and radiological data may be treated in like manner. Analytical results for mercury of 0.0016 would round off to 0.002 while 5.4 pCi/l of combined radium-226 and radium-228 would round down to 5 pCi/l.

Another document is from the Nevada Division of Environmental Protection titled Guidance for the Use of Significant Figures and Rounding Conventions in Water Quality Permitting  which states;

In reporting results and in calculating permit limits or mass loads, it is necessary to round the results to the correct number of significant figures. There are different rounding conventions in use, and BWPC has adopted a hybrid approach in which the rounding convention used for a number ending in 5 depends on the context. In reporting measured values, 5 is rounded to the nearest even number. For calculated values, 5 is rounded up.

Both referenced documents present the same procedures for the rounding of analytical data.  The use of these documents by the LSRP to manage a remedial site is supported by SRRA.  The decision to continue to use and potentially go against the December 2019 NJDEP e-mail message is a decision that needs to be made by the Person Responsible for Conducting Remediation (PRCR) and the project LSRP.

You really need a firm with experience and understanding of environmental regulations to help you  navigate New Jersey’s environmental regulations.  Curren has over 20 years’ experience.  We provide an initial consultation with parties requiring LSRP services in New Jersey.  

Mosquito control is critical in disease prevention. Mosquitoes transfer diseases such as Yellow Fever, Malaria, Dengue, plus the West Nile virus. We need to protect ourselves from these viruses by protecting our yards. Without proper mosquito control, yards can become breeding grounds for mosquitoes.

How can mosquitoes transfer disease? You are the meal for the female bloodsucking mosquito, who, in turn is feeding the eggs. When the female needs to find food it goes for you, the blood meal. Male mosquitoes only suck on nectar and hang out in shady areas of you yard, waiting to reproduce. As a mosquito flies closer to its target, it looks for the movement of dark objects. Once it finds you, it lands, inserts its proboscis and probes for blood vessels beneath the skin. When it finds one, it injects saliva into the wound. The saliva contains an anticoagulant that ensures a steady, smooth flow of blood. Unfortunately, the mosquito’s saliva also may contain pathogens such as malaria parasites or encephalitis virus. This is how mosquitoes transmit disease.

What other reasons why it is important for mosquito control? It hits you psychologically, you are constantly looking over your shoulder wondering when the next mosquito is flying for their next meal of the day. To be perfectly honest, mosquitoes are annoying and can ruin your time outside which is why you won’t 

Research shows that mosquitoes began to emerge in New Jersey in April. Prior to April there are few things that as a homeowner you can do yourself to control mosquitoes.venture out during those dusk hours.

• Empty all buckets of standing water.
• Clean your gutters (or call a gutter guy to clean them for you). Leaves clog the gutters and downspouts, leading to an area where the female can lay her eggs.
• Check areas around your home where water pools, fill these areas with topsoil and some grass seed. Keep the water pooling to a minimum. A mosquito only needs a capful of water to lay her eggs.
• Remember any water outside at your property can lead to a mosquito breeding ground.

While the above is important, once mosquitoes become adults, they are on the underside of bushes hiding and  waiting for you to come outside. This is where you need a professional company to control the mosquitoes.

Mosquito companies will spray the underside of the bushes, trees, under decks and around the foundation of your dwelling to manage the mosquitoes in your yard.

For more information please contact Curren Environmental. It’s time to learn more about mosquitoes and controlling these annoying pests in your yard – take back you yard this spring.

Mold is the four-letter word of real estate transactions. Finding mold can pause a sale and stop the sale all together.  If mold is visually found and/or confirmed via testing, the odds of the sale failing increases, unless you can get ahead of the problem.

There are many stories of real estate transactions with mold growth, but this one is very interesting.
The story goes that a buyer was interested in a home and the property was an in an estate.  This particular property had been vacant for some time (About 26 months).  The buyers were from out of state and mold was a concern.  During the home inspection, the home inspector took air samples throughout the home. He also found possible mold growth on some wood furniture. Those air samples were mailed to an independent lab, and once the lab finished testing the samples, they sent a report back to the home inspector. The home inspector then sent the lab data to the buyer.   Elevated mold spore count were found indoors as compared to outside levels.   The levels were also higher than you would typically find in a home sand water damage.

What does mold lab data mean?
First, as part of the story, you need to know that this property was vacant for over 2 years. The heat was on as part of maintenance but the home was not property dehumidified (air conditioned in the warmer months). Mold growth occurs where there are moisture and organic materials. In this case, again there were only visual signs of mold growth on some furniture, but no visual signs on the sheetrock walls, kitchen cabinets, bathroom cabinets and no signs on the ceilings throughout the home.

What caused mold to grow in a vacant home?
When the humidity is high and the property is not well ventilated, mold growth will occur. These spores can become airborne and move throughout the home. This home had a lot of carpets which contain organic matter (dirt, skin cells, etc.) and carpets hold mold spores.

Curren Environmental completed a mold assessment and found no outside water entry, plumbing leaks, roof leaks, etc. Mold growth was contributable to the home being vacant without consistent heating and air conditioning operating.  Mold Remediation at this property was performed and removed the airborne spore count to levels comparable to outside.  Remediation was performed as follows:

1. The carpet was removed and tack strips were removed.
2. All organic furniture that could not be wiped down was disposed of (fabric coating sofas and chairs.
3. HEPA vacuumed walls and floors in the master bedroom, in-law suite, and 2nd floor.
4. A broad-spectrum, FDA approved, fungicide was applied to the walls and the flooring in the rooms.
5. Air scrubbers operated during and after the remediation based on volume of air in the space and goal of completing multiple air exchanges. 

As the story goes, post air testing showed that the elevated spore levels dropped dramatically at the property. Please see below. For this story, no walls were removed, no ceilings were opened nothing was torn down to the pre-construction stage.

The ending, a happy buyer, a happy seller, and a clean home. Not every property that has elevated mold spores needs to have everything torn down and removed.   Mold testing must be assessed facting in history of the space, current conditions and an understanding of mold spores found and what environments these spore thrive.   A mold remediation professional will look at the data, photos provided and any other detailed information before handing over a cost. It is very important to understand that mold is everywhere and there are no “Mold Free” properties.  

Call for Mold Questions.

                    Why is an Oil Tank Sweep Important?

From 1900 to 1945 coal was king (coal shortages were common during WWI). By the mid 1930’s oil burners had made quality and safety improvements that made oil a competitor to coal. In 1940 more than half the homes burned coal. America oil reserves and steel making prowess from WWII allowed oil to be rapidly adopted after WWII (1945).

In the 1970’s and 80’s due to natural gas shortages and price irregularities the natural gas market become deregulated. Deregulated allowed for competition and market based pricing, which meant lower prices, this drove the popularity of natural gas. So natural gas didn’t become popular until the late 1980’s.

For homes built between 1900 and 1980, oil heat was highly probable at some point in the past (in short what were your alternate choices for heat besides oil?). Construction codes didn’t address oil tank removals until the 1990’s. Environmental regulations today have strict standards for heating oil leaks from tanks in soil and groundwater. In short, an oil tank leak can make the owner of a property a polluter so to speak. On top of that the regulations view the current owner of a property as the Responsible Party (RP) for the cleanup.

Today, you could buy a house built in 1950, that used oil until say 1980, when a conversion to gas occurred. The old oil tank was literally just left in place (abandoned), since doing anything cost money. Fast forward to 2020, you are buying that home with an oil tank that hasn’t been used in decades. If you don’t add a tank sweep with GPR (ground penetrating radar) to your home purchase due diligence you are opening your self up to a responsibility and an expense with the oil tank, as when you sell someone will do a tank sweep and find the tank you never knew you had or used, which happens all the time.

Today the internet is used not just for shopping, but for education. There are homeowners that have an oil tank on their property (used or out of service), these homeowners have learned via the internet (websites like this one) of the liability of an oil tank. We find that some people will hide the evidence of the tank and hope that no one looks for an oil tank, since the home is now heated by natural gas. Do you find it hard to believe that someone would try to hide the truth? Follow this story.

Home went under contract, home inspection and all, everything but a tank sweep with GPR was performed by the purchaser of the home. One day before settlement the prospective homeowner does a walk through of the property and low and behold someone spray painted "tank" on the ground. (this is a true story. I couldn’t make things like this up).

Home was a flip, so the owner (really owner for 7 months) had no knowledge of any oil tank. Curren scanned the marked area and bingo oil tank, about ¼ full of oil. We can only speculate as to why the tank was hidden and why someone spray painted tank on the sidewalk. The general theory is a neighbor was aware of a tank at that location and also aware the owner removed evidence of the tank. Presumable the neighbor removed their tank and didn’t appreciate the neighbor not doing the right thing and removing theirs. We believe this is a likely scenario as we have seen it on other sites that we have performed tank scans/sweeps. People will park cars in driveways over tanks. People will say a tank was removed and we scan the area and find a metal object indicative of a tank.

We even have people who have removed their own tanks, we get contracted to do soil borings and soil sampling from the removed tank area. $35,000.00 later, we find that the tank did leak, the owner just thought that oil is naturally present in a removed tank excavation.

Bottom line you cannot rely on statements from a seller such as these:

There is no oil tank.

That the tank was removed

The removed tank didn’t leak.

Do you need to complete a tank sweep? Yes, if the home was built before 1980 and you can’t get 100% written documentation that natural gas was always utilized to heat the dwelling.

"Why do I have mold?", is a common question we get from people who discover mold in their homes.   The short answer is that 95% of the time it is a moisture or a water problem.   Yes, mold can come back after remediation if you do not fix what caused the mold.  It can also come back if the mold was not properly remediated (wiping with bleach is not mold remediation).

Thousands of mold inspections and remediations have allowed a broad evaluation of mold growth patterns.  You can't be a good mold inspector if you are not accomplished in mold remediation.  Getting down and dirty remediating mold allows you to witness first hand how mold growth has occurred.  Remediating often times requires you to open up walls to get at the mold growth and you obtain a perspective as to how/why mold grows. 

For instance, wood studs allow mold to grow more aggressively than metal studs when you have a wet area.   Floating concrete slabs can enhance mold growth on ceilings. When there are areas of termite damage you should expect to find mold growth as termites like a moist environment, like mold.   Did you know that your beloved mulch beds around your home can aid in humidity in a basement and crawlspace? Thus, creating an ideal environment for mold growth.  Also, the dehumidifier bucket that you got sick of emptying (filled with water every 2 days) now sits unplugged in the basement, ruining your line of defense in controlling moisture and keeping mold at bay. These factors as well as a host of other environmental and degrading building in fracture are the common culprits that cause mold to grow in a home.

(For example, lack of drainage and added mulch beds led to mold growth)

Curren Environmental does mold remediation to homes that have had mold remediation previously and the mold grew back, meaning remediation was not successful.  This happens due to top lack of following proper mold remediation protocols, using inferiors products to prevent mold growth from reoccurring and lastly removing the moisture source (many times there are more than one source) identification.  (Curren had one project where there for four sources of moisture that fueled the mold growth.)

Mold growth is typically found in homes when the property is being sold.  It may not be bothering the seller, but it may affect the buyer.  Everyone has different intolerance and tolerances to mold growth, one of the reasons there are no federal regulations governing mold growth. Mold growth can be a huge real estate deal breaker. If it wasn't it would be on the sale sheet, showing the moisture or water issue and where the area of mold growth. 

No, mold growth will not be on the sale sheet.  It is best to remediate the mold growth before the property is on the market, removing the issue in its entirety. 

Questions on mold remediation? Follow this link or call Curren Environmental today. 

Curren Environmental has been solving tank related issues for over 20 years.   Oil tanks were like cell phones, they were ubiquitous in homes in the Northeastern United States.  Oil was king as the graph shows:

Oil heat was more popular than natural gas up until 1980!

In 1950 43.9% of homes had oil heat

In 1960 62.9% of homes had oil heat

In 1970 52.6% of homes had oil heat

So in 2019, what are the odds the home your buying has or had an oil tank? Pretty high for sure.   

Tank Scans with GPR = Buyer Due Diligence

A tank scan found this tank.  You can see from the many holes in the tank, that the tank leaked.   Thankfully the home buyer had a tank sweep completed and found the tank.  The homeowner had to remove and remediate the oil tank.   

Buying a home is one of the top ten most stressful situations in an adult’s life. The stress of the inspections, cost of inspections, time and effort put into buying the home is extensive. The amount of inspections one will go through to buy a property could be, at least, totaling six (6). One of those inspections should include searching for an underground oil tank.

Underground oil tanks have a finite life span and were not built to last forever. If you forego the tank scan, you may have just bought yourself an underground oil tank. If the tank leaks you could be faced with a large and pricey problem. Not all recent homeowners are even aware that they bought a home with an underground oil tank.

Top 8 Reasons for a Tank Scan:

1. House built before 1980.
2. Above Ground Oil Tank.
3. Fill Pipes.
4. Vent Pipes.
5. Copper lines are visible.
6. Neighborhood that typically has Underground Storage Tanks
7. Furnace Chimney.
8. Previous tank scan was done with a magnetometer.

House built before 1980
If the house was built before 1980 you should presume that there could be an underground oil tank unless the seller provides you information otherwise. But beware, if a tank scan was done with a magnetometer, the scan may not have been enough to identify an underground oil tank. Ground Penetrating Radar is the most advanced technology used in today’s market to identify buried tanks.

Owner has no knowledge of prior oil heat

Oil was king from 1900 to late 1980, tanks were installed after 1980 but they are not as common.

We tell people assume the property had oil heat, prove to me it did not.

Above Ground Oil Tank
Prior to oil used as the main heating source, coal was providing the heat in the home. Coal was difficult on the homeowner, as you would have to shovel coal every 4-8 hours to keep the heat on. After coal, oil tanks became a popular heating source. The tank was buried as it was not an added value in the property aesthetics. When homeowners believed that the underground oil tank was no longer working, or it was time for a new tank an aboveground oil tank was installed. In essence, if there is an aboveground oil tank than there is a possibility that an underground oil tank exists on the property.

Fill Pipe

Oil tanks have fill pipes where the oil is distributed to the vessel. The fill pipe is attached to the oil tank and is what the oil delivery company uses to fill the tank with oil. If the fill pipe is noticeable during the home inspection, then that is a sign of an underground oil tank.

Vent Pipe
The vent pipe on the oil tank allows air/fumes to escape from the tank when the fuel is being added. The vent pipe commonly has a mushroom like cap to keep water from entering the oil tank. If a vent pipe is visible than that is sign that there my have been an underground oil tank at the property. If only a vent pipe is found then that means the tank may have been abandoned in place, meaning filled with sand or another inert material.

Copper Lines
The oil fuel lines are made of copper tubing (lines) that allow the fuel to move from the tank to the furnace and back to the tank. The supply line provides the fuel from the tank to the furnace and the return line supplies the fuel that was not used back to the tank. If there is any evidence of current lines or lines that were cut, then there may have been an underground oil tank.

Neighborhood
Neighborhoods start with one home, moving to many, many more homes. Each neighborhood has a timeline, starting with the first home built. If this home was built prior to the 80’s than there is a possibility that a tank was on the property. The neighborhood may not have had a gas hook up line till after the homes were built, meaning there needed to be another source of heat prior to gas. If the neighborhood homes were built prior to gas in the neighborhood that it is likely that there is another source of heat and that could mean an underground oil tank.

A Furnace Chimney
In many old homes the chimney was not just used for wood burning, it was used for coal or oil. Check the chimney and see how many flues there are.

Previous tank scan with a Magnetometer.
There have been many instances where Curren Environmental is called upon to determine whether what the previous metal detector tank scan found is an underground oil tank. Metal detectors find any metal in the structure or asphalt/concrete. A/C units, reinforced concrete and chain link fences all have metal. There have been water lines and sewer lines that have been thought to be underground oil tanks, or on the flip side they were thought to be sewer or water lines and not an underground oil tank. To save money on inspections, start with the Ground Penetrating Radar not with a metal detector.

More questions?  Call our office today and speak to someone in person.

Call the Experts

888-301-1050

Everyone wants to be green, but as  a famous frog once said its not easy being green.  Working in the environmental field we are exposed to some of the best green practices people can follow.  A sad truth of being green is people want to be green on the cheap. These ten green tips can be done free and at low cost, but you will be paying big dividends to the environment.

Here is a bonus tip, share this page,  If one person you share this page with does one of the green practices you have helped the environment. 

Sign up for our Green Tips, we send a Green Tip via email about once a month.

Green Tip Email Signup

Top 10 Green Practices You can do on the cheap!

1. Use your reusable shopping bags.   Usage rate is under 20%, the top reason, people forget them, 80% of people say they do own the bags.  The next time you go to the store, place a stack of bags on the car seat, so you won't forget. For extra measure place a purse or cell phone on top of the bags. Reusable Shopping Bags

Cost = Free (If you own these bags already)

2. Use reusable produce bags. Since your going shopping, why not bring your reusable produce bags?   Same as idea as shopping bags, except you realy get any free ones, you typically have to buy them.  Unfortunately you rarely see these bags for sale or get them given to you as a freebee, if you click the photo you can find some decent quality bags on Amazon.

Cost = $12.00  or Free (If you own these bags already), most people don't 

3.  Buy reusable coffee pods.  Single serve coffee makers can actually be green, since you are not wasting water or coffe.  But when you use the single use coffe cups, you are not being green.  But reusable pods.

Cost = $15.00 for 12, split them with a friend and cost gets cut in half

4. Reusable Straws: Plastic straws and other items smaller than two by two inches, such as plastic utensils, fall through the machinery that sorts our recycling.Plastic straw Don’t Get Recycled.

Cost = $6.00

5.  At restaurants ask for a straw free table.   What is a straw free table?   Any table you sit at that the server knows you don't want to use straws.   Be real, you are in that seat for a short while, you don't need a straw.  Oh and when the server places the straw on the table and you don't use it and think  it will get reused?  Think again, its gets thrown away of you use it or not. Go straw free.

Cost = Free

6.  Insulate your hot water heater.   Mom always said to wear layers. So while your water heater has insulation, more is better and cheap. Insulating your water heater reduces standby heat losses by 25%–45% and save you about 7%–16% in water heating costs—and should pay for itself in about a year. You can find pre-cut jackets or blankets available from around $35.00. We like the blankets without fiberglass as the fiberglass jackets can tear when things bang into the jackets.  This one can also be reused when you replace the water heater if you are careful taking it off.  

Cost = $20.00 to $35.00

6. Wash 95% of your laundry in cold.  True only about 5% of clothing requires warm water: READ THE TAG. The average cost of water heating is $41.10 a month with three hours of use per day. People insist on using hot water for washing and cleaning because they believe it removes dirt, grease, and grime better, as well as disinfect the clothes. And that’s true, but hot water also ruins your clothes, causes the color to fade, and shrinks the fabric. You can save energy and money by  cutting back on the amount of hot water you use to do laundry. With cold-water detergents,  the cleansing enzymes are designed to work better in cold water.   Just look for COLD on the label, they are the same price as warm water, you just don't have to pay for hot water.

Cost = Free  * these are typically the same price as warm water detergent

7.  Stop using plastic water bottles.  Did you know in the 1980's, the big beverage companies saw the decline of carbonated soda?   Perrier became popular in the 1980's.   We have been slowly weaned onto using single serve water bottles, which we all know are terrible for the environment.  The two biggest reasons people bottled water is concerns about water quality and laziness.  I cant help about laziness, but if your home refrigerator dispenses water, it has an inline water filter, typically carbon filtration which is a universal filter.   You can fill up your REUSABLE water bottle from your refrigerator.  Fact, did you know many bottled waters are tap water? 

No doubt you have multiple bottles at home you can use. We particular like the Swell brand, liquids stay cold all day, this 25 ounce bottle is a bounty of a thirst quencher and the wood finish makes you look like a real tree hugger.

Cost = Free* to $31.00   *Odds are you already have a reusable bottle

8.  Go paperless billing.  Most all bills you receive can be converted into an electronic ebill (bill is emailed to you). Ebills, save postage, fossel fuel as no vehicle must transport the bill and lastly paper.  Most people pay bills online anyway saving postage, so why not receive your bill on,ine as well?   66% of bills are still mailed.  Lets get it below 50%.

Cost = Free

9.  Air seal your home.   You have air leaks for sure.  Every catch a mouse in the house?  They come through gaps.  Go in your basement during the day and turn off the lights.  Look for light shining through.  Common openings are where hose bibs exit the foundation, where the sill plates meets the foundation, holes where you may have drilled to run a pipe or cable.   Fill these gaps with foam.

Cost =  $6.00/can

10. Improve your windows.  Many windows leak air simple because the window is not 100% square in the frame.  Replacing windows is expensive.   Two simple things you can do.  One place foam insulating tape on the bottom of the window where the windows sits in the bottom of the frame.  This little trick can help seal the window by helping the window be square in the frame and having a tighter seal.  The 2nd tip is to have working locks on your windows and locking them, which further squares the window.    We do mold inspections and check windows.  On average 30% of windows are not locked, which allows air to leak in.   

Cost = $10.00 *   about 30 windows

Sign up for our Green Tips

we send a Green Tip via email about once a month.

Green Tip Email Signup

Mold is truly a four letter word and also a very misunderstood term.  You've heard of "Black Mold" (not a real mold term) or "Toxic Mold" (no such thing)? In the mold testing and mold inspection industry "black toxic mold" should not be used.  Misinformation abounds, so here are some important facts about mold, mold remediation and mold testing

Growing mold off-gases, causing that musty odor you smell, and if you think your basements smells that way because it is a basement, you're wrong,  it's not supposed to smell musty.  Mold growth stains surfaces and is visible if you understand where and what to identify as mold.  If you see mold growing inside a building, something is wrong, it is not normal or typical, even at the shore/beach.  Curren knows because we have inspected thousands of properties and, no, they all do not have mold growing.

Pertaining to mold testing, when obvious mold is present the EPA agrees testing is not necessary.

If you have discolored building materials and are not 100% if its mold, surface sampling can be performed for verification of questionable staining indicative of mold.

Mold Testing can verify if a stained or discolored surface is impacted with mold growth, such as  surface sampling and/or air testing (non viable spore trap sampling). These mold tests quantify both mold spore count in a room and also evaluates for hidden mold in a complaint room where no visible mold is present.

Pro Tip:  Buying a house that is being flipped and the basement is finished, get a mold inspection with mold testing.

Pro Tip:  Buying a home that was bank owned and rehabbed?  Get a mold inspection with mold testing.

Our ratio of finding hidden mold in both situations is around 90%, but 70% of the time we get called in AFTER someone has bought one of these types homes, in cases such as these, mold is found after you own the property.

Proper mold remediation is the removal of an unwanted condition, such as mold. This follows a multi-step process which typically entails containment of work area, followed by physical removal, cleaning and encapsulation of remaining organic surfaces and air scrubbing, all of which are appropriate and proposed for the subject site.

Curren Environmental has over 20 years’ experience in the environmental field and we provide Certified Education (CE) classes on environmental topics, including mold, so we know what we are talking about. There are only 11 states in the country that have mold regulations and licensing  programs and New Jersey is not one of them. Curren nor any other company in New Jersey holds a New Jersey license for mold remediation as the license does not exist. Generally speaking, mold remediation follows asbestos abatement guidelines to contain a workspace, establish air filtration and remove (remediate) mold. Curren has personnel that hold asbestos licensing and our personnel follow these procedures from independent training schools as well as in-house training program.

Expert advice from mold experts

888-301-1050